A Nissan Sentra Forum banner

Search results

1-20 of 121 Results
Advanced Search
  1. Reconnecting Shifter Cables

    B16 Sentra (2007-2013)
    Once again, thank you Cricki, I really do appreciate you. Jim
  2. Reconnecting Shifter Cables

    B16 Sentra (2007-2013)
    When I pulled my engine, I placed the shifter into neutral and hoped for the best. I did mess around and move the shifter arm on the transmission several times. After reconnecting the cables, the shifter doesn't feel like it is going into the gears correctly. I don't have the engine running yet...
  3. How to Bleed The Clutch B 16

    B16 Sentra (2007-2013)
    Since yesterday I found out that there is a clutch damper in the line from the cylinder at the firewall to the slave around the pilot shaft. That valve is the reason it is so hard to bleed this system if I don't miss my guess. The valve is to allow the clutch to slip a little for people who...
  4. How to Bleed The Clutch B 16

    B16 Sentra (2007-2013)
    Thank you Alpha, I will for sure check that link out, I really do appreciate it. Just a thought: why can't I pull the line going to the transmission from the outside of the cylinder on the firewall and using a turkey baster and bleed all the air out of that line down to the transmission. There...
  5. How to Bleed The Clutch B 16

    B16 Sentra (2007-2013)
    The more I read the more I am afraid that I am going to have to pull that engine back out. I used the old throw out bearing. The slave cylinder and throw out bearing are all one thing. I didn't think to bleed that slave cylinder inside the bell housing and there is no way under the sun to get to...
  6. How to Bleed The Clutch B 16

    B16 Sentra (2007-2013)
    Cricki, being a mod myself on a DIY forum, I understand the frustrations of a subject that has been repeated many many times as is the case here. I do searches before asking questions so as not to ask the same question that has been asked before. When the answers I get aren't understandable to...
  7. How to Bleed The Clutch B 16

    B16 Sentra (2007-2013)
    Thanks Cricki, I will check it out. The reason I asked if it would bleed by gravity is, when I pulled that line loose when I was removing the engine, it emptied the master cylinder. Thanks again, so far there doesn't seem to be much of anything easy on this build. lol
  8. How to Bleed The Clutch B 16

    B16 Sentra (2007-2013)
    I am ready to bleed the slave cylinder on the B16 clutch, any one know how this is done. Can it be gravity bled?
  9. What Engine will Fit 2008 SE-R Spec V

    B16 Sentra (2007-2013)
    I got most of the engine and parts back in the car except I had to put 1 inch spacers under the front motor mount and still the engine at one point it less than 1/8 of an inch from touching the carriage. If that engine shakes a lot from no balance shaft, it will wear a hole in that part of the...
  10. What Engine will Fit 2008 SE-R Spec V

    B16 Sentra (2007-2013)
    Happy, happy, happy, the engine is in place now, one thing I need to change and soon. I need to raise the engine on the passenger side at least 1/4 more inches. I looked and it was so close to the carriage I thought it was touching. I put a light behind it and it isn't touching but it can't be...
  11. What Engine will Fit 2008 SE-R Spec V

    B16 Sentra (2007-2013)
    LOL, I got the transmission in too far right now, I am trying to get the whole thing toward the passenger side about and inch or so but something is stopping it. I will just keep kickin, thanks Tritton. Good to know it is just a matter of wiggling until it pops in place.
  12. What Engine will Fit 2008 SE-R Spec V

    B16 Sentra (2007-2013)
    I couldn't edit the post I just made. I wanted to say that the engine on the transmission end will not go down any further and it needs to go down at least an inch or two, but it is sitting on the carriage. Does the end of transmission got under the carriage some way?
  13. Align Clutch Plate Without Alignment Tool

    B16 Sentra (2007-2013)
    Got the transmission installed and most other parts. I hope to drop the engine back in the car tomorrow. I noticed that the exhaust manifold had a gap that is unacceptable. Maximum is .012 inch, mine is .020, looks like I need to do some flattening. Question, what type of break in oil is best...
  14. Align Clutch Plate Without Alignment Tool

    B16 Sentra (2007-2013)
    Cricki, you are a life saver, thank you so much once again. I looked everywhere in the factory manual and I saw one place where it said 80 ft lbs but it didn't go into detail at all. I can't thank you enough. Now I will go out and torque the flywheel. Have a fantastic evening. Jim
  15. Align Clutch Plate Without Alignment Tool

    B16 Sentra (2007-2013)
    I don't know how I missed your post Cricki, thanks a ton, I really appreciate your help. Question, what do I torque the flywheel bolts too and also the pressure plate bolts? I think I found the specs for the pressure plate, 19 foot pounds with loctite, right? I found several different answers...
  16. Align Clutch Plate Without Alignment Tool

    B16 Sentra (2007-2013)
    Question, is the 6 speed MT in the SE R Spec V different from the 6 speed MT in an Altima. The reason I need to know is the size of the pilot shaft may be different in each of these. I need to know which transmission I have, Any one know where to look? EDIT *** I just looked it up, they are the...
  17. Align Clutch Plate Without Alignment Tool

    B16 Sentra (2007-2013)
    Thanks Cricki, I am afraid that wouldn't be close enough. Maybe I can find a real pilot shaft from a transmission at a junk yard. I just measured the diameter of the pilot shaft is 23 mm or 30/32 inch. The shaft has 21 teeth. Thanks for replying Cricki, I do appreciate your help. If I find one I...
  18. Align Clutch Plate Without Alignment Tool

    B16 Sentra (2007-2013)
    Is there a way to align the clutch plate on 2008 2.5 engine without an alignment tool? I can't find one anywhere. I am ready to put the transmission back on the engine so I can put it back in the car but can't find that tool. Any help is more than appreciated.
  19. What Engine will Fit 2008 SE-R Spec V

    B16 Sentra (2007-2013)
    Trying to find something specific online is like pulling teeth, anyone have instructions how to prime a new oil pump? I don't have it mounted yet so I thought maybe it has to be primed before installation. I know how the american cars oil pump was primed years back but the pickup tube does not...
  20. What Engine will Fit 2008 SE-R Spec V

    B16 Sentra (2007-2013)
    Getting the valve springs off and back on turned out to be no problem at all. I do have a question though. Are the exhaust valve seats replaceable? It feels like there is a lip on the inside of the seat like they can be inserts. If they are inserts, how do they come out? The intake valves and...
1-20 of 121 Results
Top